Getting Started
Introduction to Arm Architecture
Assembler Rules and Directives
-
The ARM,Thumb and Thumb-2 Instruction Sets (2:27)
-
Predefined Register Names (2:08)
-
Frequently used Directives (3:36)
-
Overview of Binary Operators (1:44)
-
Programming : Renaming Registers (4:22)
-
Programming : Allocating space in memory with the SPACE Directive (9:12)
-
Programming : Swapping Register Content (3:44)
-
Source Code Download
Load-Store Instructions
-
Memory Demarcations (3:35)
-
Frequently used Load/Store Instructions (Part I) (5:24)
-
Frequently used Load/Store Instructions (Part II) (5:07)
-
Notice about the next lesson
-
Frequently used Load/Store Instructions (Part III) (4:42)
-
Pre-Indexed Addressing (2:16)
-
Post-Indexed Addressing (2:21)
-
Endianness (2:49)
-
Defining Memory Areas (2:27)
Dealing with Constants and Literals
-
The Encoding of the MOV Instruction (4:41)
-
Loading Constants with the LDR Instruction (2:43)
-
Loading Constants with the MOVW and MOVT Instructions (0:57)
-
Loading Labels with ADR, ADRL and LDR Instructions (2:32)
-
Programming : Solving a Simple Equation (5:17)
-
Programming : Importing from C to Assembly (5:54)
-
Programming : Exporting from Assembly to C (6:21)
Arithmetic and Logic Instructions
-
Flags (3:02)
-
The N and V Flags (3:34)
-
The Z and C Flags (0:42)
-
Compare/Test Instructions (6:24)
-
Overview of Boolean Operations (1:33)
-
Introduction to Shifts and Rotations (1:25)
-
Understanding Logical Shifts (4:50)
-
Understanding Rotations (1:33)
-
Some Shift and Rotate Examples (2:57)
-
Overview Addition and Subtraction Instructions (1:50)
-
Overview of Multiplication Instructions (4:16)
-
Multiplying by Constants (2:34)
-
Overview of the Division Instruction (1:24)
-
Bit Manipulation Instructions (4:42)
-
Programming : Finding the Maximum Value in an Array (12:45)
-
Programming : Experimenting with the LSL Instruction (5:02)
-
Programming : Adding Signed Numbers (7:37)
-
Programming : Finding the Minimum Value in an Array (8:51)
-
Programming : Solving a More Complex Equation (7:24)
-
Programming : Performing Division by Subtraction (6:20)
Branch and Loop Instructions
Stack Instructions
Developing the General Purpose Input/Output(GPIO) Driver
-
Overview of ARM Cortex-M General Purpose Input/Output Module (7:24)
-
Getting the right Documentation (3:09)
-
Programming : Analyzing the Chip's Memory Map (14:52)
-
Programming : Defining Addresses for Registers (19:02)
-
Programming : Setting the Pin as an Output Pin (10:17)
-
Programming : Toggling a Pin using the Output Data Register (ODR) (8:56)
-
Programming : Toggling a Pin using the Bit Set /Reset Register (BSRR) (8:35)
-
Programming : Defining Registers for Input Driver (9:20)
-
Programming : Implementing the Input Driver (20:57)
Developing the Analog to Digital Conversion (ADC) Driver
-
Introduction to Analog to Digital Conversion (8:38)
-
Understanding ADC Independents Modes (4:02)
-
Programming : Planning the Project (7:32)
-
Programming : Implementing the Initialization Function (32:04)
-
Programming: Implementing the ADC Read Function (11:24)
-
Programming : Testing the ADC Driver (21:52)
Developing Universal Asynchronous Receiver-Transmitter(UART) Driver
-
Overview of the UART Protocol (7:43)
-
Programming : Planning the Project (9:18)
-
Programming : Configuring the GPIO Pins for the UART (21:25)
-
Programming : Configuring the UART Parameters (18:23)
-
Programming : Sending Characters (18:20)
-
Programming : Retargeting Printf (7:27)
-
Programming : Developing the UART RX Driver (23:12)
Developing the System Tick (SysTick) Timer Driver
Developing the General Purpose Timer Driver
Working with Data Structures
-
Introduction to FIFOs (2:38)
-
Notice
-
[OPTIONAL] Implementing the FIFO in C (Part I) (20:21)
-
[OPTIONAL] Implementing the FIFO in C (Part II) (16:11)
-
Programming : Implementing the Initialization Function (8:59)
-
Programming : Implementing the FIO Put Function (13:54)
-
Programming : Implementing the FIFO Get Function (11:10)
-
Programming : Implementing the FIO Size Function (4:28)
-
Programming : Testing the FIFO (15:31)
Working with State Machines
-
Introduction to Moore and Mealy FSM (7:13)
-
Designing Traffic Light System using Moore FSM (21:47)
-
Notice
-
[OPTIONAL] Implementing a Traffic Light System using Moore FSM (Part I) (50:17)
-
[OPTIONAL] Implementing a Traffic Light System using Moore FSM in C (Part II) (10:58)
-
[OPTIONAL] Implementing Moore FSM using Pointers (9:09)
-
Programming : Configuring the Required Pins (15:36)
-
Programming : Implementing the State Machine (38:58)
-
Programming : Testing the State Machine (7:08)
Closing
